Suchergebnisse

Technical data: Operating temperature: -40 °C to 125 °C Setting points per revolution: 12 (you should measure for your self because this varies from vendor to vendor) with switch button Fixed hole size: 2.0 mm Product size: 32.0 mm * 15.0 mm Working v...

Details block-shaped acrylic frame 2 drill holes 2 black bubble lines yellow-green filling leak-proof Block-shaped tubular spirit levels with 2 screw holes made of clear acrylic glass 55 x 15 x 15 mm hole distance: 41 mm

This documentation is a copy from https://miscsolutions.wordpress.com/mini-height-sensor-board A differential modulated IR height sensor. The sensor detects the target height by looking for the reflected light from two separate LEDs to be equal. The two...

cooling fan: XYJ24B4010M by Xinyujie (has double ball bearing inside!) PT100 Sensor heater cartridge: 24 V, 80 watts

  Features 3-axis gyroscope 3-axis acceleration sensor 3-axis magnetic field sensor (geomagnetic field/compass) Digital Motion Processor (DMP) Specifications Three 16-bit analog-to-digital converters (ADCs) for digitizing the gyroscope outputs ...

This is used to check the voltage of Raspberry Pi and to validate occuring undervoltage happenings. It's a really useful helper.

This relay is slighty different than Relay JQC-3FF-S-Z (Logic Level difference due to other layout of resistors) measured: relay switches off properly at >= 3.2 V and switches back at <= 1.1 V This relay is used to control the LED stripes and spots of Trik...

This relay is used to switch on the Power Supply by Raspberry Pi GPIO. Specifications in line with international safety standards (control area and the load area has a separate slot) double-sided FR-4 circuit board design LED status pull up bright (g...

This stick is used to make local backups from filesystem (configs, scripts, Influx data, etc.)

The webcam is used for remote monitoring and for creating timelapse videos. Especially for long run prints we can use the timelapse feature to review unsuccessful prints.

https://www.ebay.de/itm/173008003388 Power: 3 W Voltage: 9.6 - 10.5 Volt Max. brightness: 300 - 400 LM Current consumption approx. 260 mA Colour temperature: 6000 - 6500 K Beam angle: 120 - 140 degrees Lifetime : > 100,000 hours Diameter approx.: 28 ...

Those items are used to keep the weighy main cable into position while Trikarus is moving. The higher the effector gets the more cable we have in idle state. We need to keep back the cable from collision points. So we use retractable cable holders to pull back...

10A 125VAC ( UL, CUL ) 6A 250VAC(UL, CUL) 10(4)A 250V~ T125/55 (VDE,ENEC)) Snaps into 13 x 19mm panel Initial contact resistance : 20m ohm (max.) Insulation resistance : 100M ohm (min,) at 500VDC Dielectric strength : 1,000VAC for 1 minute Electrical li...

This router is the connection end point for Raspberry Pi, Duet 2 Ethernet and local connection clients (wired or by Wifi). It acts as mesh repeater or switch (regarding to the configured mode). The housing is identical in construction to TPLINK WR840N / WR841N...

This card is used for Raspberry Pi operating system. Because we collect a lot of data which we are going to store in InfluxDB we have a huge amount of writing cycles. In the past we tested out regular SD cards which were defect after approx. one year of life t...

This module is used to control the current and voltage of the LED spots (COB LED Spot 6000-6500K 260mA 10V) https://www.ebay.de/itm/DC-DC-LM2596S-60V-3A-Stepdown-Modul-Buck-Modul-zum-Regulieren-von-CC-CV/332730030268?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p205...

closed design (case) with fan, screw terminals Universal input Overload protection by switch-off, auto recovery protected against short circuit, overload, overvoltage Built-in PFC circuit low installation height Technical data Output voltage: 24 V D...