Suchergebnisse

Marlin Firmware for Hangprinter Torbjørn also forked Marlin Firmware and pulled back a lot of stuff into official Marlin feature tree https://github.com/MarlinFirmware/Marlin/pull/9180 github.com/tobbelobb/hangprinter/blob/73a0cf91bbc04a59faccd6f042d30d5d...

The following models should be possible to be generated well for Hangprinter use, that means: less or no support material required (because it is more expensive and time intense) regular print or spiral vase mode For some models to match those condition...

This page contains some information about different decisioning which were met when designing hardware and software related things. Why stepper motors and not brushless (BLDC) motors?   Stepper motors are significantly less expen...

risk possible damage (1-10) 1 = minimum, 10 = maximum probability of occurrence (category) 1 = low 2 = medium 3 = high rating= scope of damage x probability of occurrence counteraction(s) and hints line construction lines break / loosen ...

This collection is based on a lot of topics especially about Hangprinters. Repeatedly many people do the same mistakes building and running a Hangprinter due to missing knowledge or time. Bad mechanical installation and miscalibration lead to bad print results...

Hangprinter is a parallel line driven open source fused deposition modeling 3D printer notable for its unique frameless design. It was created by Torbjørn Ludvigsen first in 2016 and got multiple iterations (versions). The printer is part of the RepRap project...

Wooooah. After planning, manufacturing, building, coding and having trouble everywhere, you finally reached the goal! Now you can nearly start to print! Here are some tips for the real usage of Trikarus. When Trikarus is not printing When Trikarus is not act...

Filaments for Hangprinter Hangprinters need a lot of material to print big. And usually to print bigger most users decide to install hotends with higher troughput. That's why the need of bigger filament spools comes up. There are few vendors who sell really b...

The line collision detection tool is pretty neat but it has a caveat. It does not know about support structures which may widen the model with extra geometry. This may lead to collisions which cannot be calculated with ease. The Statue of Atlas On  this page...

Trikarus prerequisites: maths and calculations Configuring the firmware requires a lot of mechanical / math values. So the following table provides calculations for various values needed to build up Trikarus. Meaning Formula / results Notes ...

13.05.2023 - Maker Bottle (450mm)   16.04.2023 - Watering can 620g white PLA filament, 1mm layer height. The can is not solid to keep the water inside. We are trying to close the surface manually. Print time 6h46min. 20.08.2022 - Torso 24.07.20...

Core packages Bundle Conductor no. Colours according to DIN ISO 47100 1 1 white 1 2 brown 1 3 green 1 4 yellow 2 5 grey 2 6 pink 2 7 blue 2 8 red 3 9 black 3 10 violet 3 ...

Measurement Parameters after 30 minutes runningt 24 volts 8°C room temperature 120 LEDs SMD 3528 (ca. 1 meter) Result 0,37 A current 8,64 W power 27 °C temperature https://www.led-studien.de/led-waerme-lebensdauer

https://www.ebay.de/itm/2-m-Kabel-Schutz-Schlauch-Gewebe-Installations-Kanal-selbstschlie%C3%9Fend-flexibel/301815929370?ssPageName=STRK%3AMEBIDX%3AIT&var=600627190685&_trksid=p2057872.m2749.l2649 Ideal protection for wires and cables in all areas of ap...

PE braid high gliding performance new revised formula incredibly thin diameters high abrasion resistance highest possible knot load capacity incredibly sensitive bite transfer further and more precise litters saltwater resistant no salt crystal deposi...

Cross sections: 1 x (0.75 - 2.5) 2 x (0.75 - 2.5) mm² Rated insulation voltage [Ui]: 500 V Rated impulse withstand voltage [Uimp]: 6000 V AC Operating torque (screw terminals): ≦ 0.8 Nm Climate resistance: moist heat, constant, according to IEC 60068-2-78 m...