Suchergebnisse

https://www.ebay.de/itm/173008003388 Power: 3 W Voltage: 9.6 - 10.5 Volt Max. brightness: 300 - 400 LM Current consumption approx. 260 mA Colour temperature: 6000 - 6500 K Beam angle: 120 - 140 degrees Lifetime : > 100,000 hours Diameter approx.: 28 ...

Those items are used to keep the weighy main cable into position while Trikarus is moving. The higher the effector gets the more cable we have in idle state. We need to keep back the cable from collision points. So we use retractable cable holders to pull back...

10A 125VAC ( UL, CUL ) 6A 250VAC(UL, CUL) 10(4)A 250V~ T125/55 (VDE,ENEC)) Snaps into 13 x 19mm panel Initial contact resistance : 20m ohm (max.) Insulation resistance : 100M ohm (min,) at 500VDC Dielectric strength : 1,000VAC for 1 minute Electrical li...

This router is the connection end point for Raspberry Pi, Duet 2 Ethernet and local connection clients (wired or by Wifi). It acts as mesh repeater or switch (regarding to the configured mode). The housing is identical in construction to TPLINK WR840N / WR841N...

This card is used for Raspberry Pi operating system. Because we collect a lot of data which we are going to store in InfluxDB we have a huge amount of writing cycles. In the past we tested out regular SD cards which were defect after approx. one year of life t...

This module is used to control the current and voltage of the LED spots (COB LED Spot 6000-6500K 260mA 10V) https://www.ebay.de/itm/DC-DC-LM2596S-60V-3A-Stepdown-Modul-Buck-Modul-zum-Regulieren-von-CC-CV/332730030268?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p205...

closed design (case) with fan, screw terminals Universal input Overload protection by switch-off, auto recovery protected against short circuit, overload, overvoltage Built-in PFC circuit low installation height Technical data Output voltage: 24 V D...

The used OLED displays for Smart Stepper have wiring order GND-VCC-SCL-SDA. We figured out that there are nearly identical modules on the market which have another order. The following photo shows another OLED display with order VCC-GND-SCL-SDA. We need to che...

Traco Power TMA 2405S Pin 1 = 24V In Pin 2 = GND1 Pin 4 = 5V Out Pin 6 = GND2 ceramic condensator (KERKO) Pin 1-2: 1-50µF, 35V ceramic condensator (KERKO)  Pin 4-6: 1-50µF, 10-16V Warnings This USB hub is cheap and has backfeeding issue. We should ...

  These stepper motor are strong Nema 17 which are installed at the A,B, C and D drives.

Hardware To connect a PT100 sensor to a Duet, you need a RTD interface board based on the MAX31865 chip. The interface board you need depends on which Duet you have. Duet 2 (WiFi, Ethernet and Maestro) and Duet 3 These Duets support up to two MAX31865-based...

This type is a point laser for the projection of a red laser dot and is a laser module which is much better visible through the wavelength of 635nm than a comparable laser with 650nm. The optical diode power of the laser module is . Typical applications are lo...

Notes about Trikarus wiring PSU The switching power supply can be switched on and off via a relay. This saves power consumption, the life time can be improved, there is less audio noise and the safety of the machine is better. The PSU relay is switched o...

Note: The Smart Steppers are wired with 5V IN at the module side,  but not at Duet. The power for the modules come from USB hub. For this reason the 5V wires are not shown in the following diagram:

  Notes There are different versions of the UPS ("USV" is german short name for this) on the market. Shanqiu Mini USV FX5-48 and Vultec Continuity UPS30PW-DC are nearly the same models except different color, POE wattage and branding. Both come w...

MPU6050 pin configuration Pin number Pin name Description 1 Vcc Provides power for the module, can be +3V to +5V. Typically +5V is used 2 Ground Connected to Ground of system 3 Serial...

Electrical Components on the MisfitTech Smart Stepper Board Allegro 4954LPT DMOS PWM Motor Driver AMS AS5047D High Speed Position Sensor Atmel ATSAMD21G18 Cortex MCU Neodymium magnets and encoder sensor The reference magnet for the AS5047D e...